(1/8) 2007-05-23 (ver.0.2) product information features (1) 13.3?wide-xga(1280x800 pixels) display size for notebook pc (2) led backlight with led controller ic (3) glare surface (4) bezel less structure mechanical specifications item specifications dimensional outline (typ.) 304.0( w ) x 202.4 ( h ) x 3.3( d ) mm number of pixels 1280 ( w ) x 800( h ) pixels active area 286.08( w ) x 178.8( h ) mm pixel pitch 0.2235( w ) x 0.2235( h ) mm weight (approximately) (225) g backlight led absolute maximum ratings item min. max. unit ( v dd ) -0.3 4.0 v supply voltage ( v led ) -0.3 22 v led currency ( i led ) - (30) ma input signal voltage ( v in ) -0.3 v dd +0.3 v operating temperature 0 50 c storage temperature -20 60 c storage humidity 10 90 %(rh) electrical specification item min. typ. max. unit remarks supply voltage ( v dd ) 3.0 3.3 3.6 v supply led voltage ( v led ) 7.5 12 21 v common mode input voltage ( v cm ) 0.7 - 1.75 v differential input amplitude ( v id ) 100 --- 600 mv *1 ( i dd ) --- 300 400 ma current consumption *2 ( i led ) --- 15 17.5 ma power consumption --- tbd. --- w pwm=100%:15 ma *1 : 8 color bars pattern *2 : the current value of each row should be the same value. optical specification ( t a=25 c) item min. typ. max. unit remarks contrast ratio ( cr ) 300 500 --- --- response time ( t on )+ ( t off ) --- - (50) ms luminance ( l ) 210 300 --- cd/m 2 pwm=100%:15ma *the information contained herein is presented only as a guide for the applications of our products . no responsibility is assum ed by toshiba matsushita display technology or other rights of the thir d parties which may result from its use. no license is granted by implication or otherwise under any pat ent or patent rights of toshiba mats ushita display technology or others. *the information contained herein may be changed without prior notic e. it is therefore advisable to contact toshiba matsushita display technology before proceeding with the des ign of equipment incorporating this product. 33.7cm colour tft-lcd module (13.3 type) LTD133EWDA (p-si tft) tentative toshiba matsushita display technology co., ltd. all information is sub j ect to chan g e without notice. please read bottom notes. www.datasheet.co.kr datasheet pdf - http://www..net/
(2/8) 2007-05-23 (ver.0.2) LTD133EWDA dimensional outline (front side) tentative unit : mm standard tolerance : 0.5 www.datasheet.co.kr datasheet pdf - http://www..net/
(3/8) 2007-05-23 (ver.0.2) circuit generation voltage manipulation gray scale converter dc/dc gate driver gate driver liquid crystal panel 1280 x 800 pixels source driver panel controller lvds include led led led led led led board led driver cn1 connector LTD133EWDA block diagram 1, 1 2, 1 x, 1 1280, 1 1, 2 1, y x, y 1, 800 1280,800 1280 pixels 800 pixels www.datasheet.co.kr datasheet pdf - http://www..net/
(4/8) 2007-05-23 (ver.0.2) LTD133EWDA timing chart www.datasheet.co.kr datasheet pdf - http://www..net/
(5/8) 2007-05-23 (ver.0.2) LTD133EWDA timing specification 1) 2) 3) 4) 5) 6) item symbol min. typ. max. unit horizontal scanning term t h - 1448 x t c - clock h-sync pulse width t hw 4 x t c 32 x t c - clock horizontal front porch t hfp 4 x t c 48 x t c - clock horizontal back porch t hbp 4 x t c 80 x t c - clock horizontal blanking period(*8) t hb - 168 x t c - clock horizontal display term t hd 1280 x t c 1280 x t c 1280 x t c line frame period t v - 830 x t h - line v-sync pulse width t vw 1 x t h 6 x t h - line vertical front porch t vfp 1 x t h 3 x t h - line vertical back porch t vbp 2 x t h 14 x t h - line vertical blanking period(*9) t vb - 30 x t h - ns vertical display term t vd 800 x t h 800 x t h 800 x t h clock period t c - 13.87 - note 1) refer to ?timing chart? and lv ds specifications in tia/eia-644. note 2) if de is fixed to "h" or "l" leve l for certain period while nclk is supplied, the panel displays black with some flicke r. note 3) if nclk is fixed to "h" or "l" level for certain period while de is supplied, the panel may be damaged. note4) tvb = tvw + tvfp + tvbp thb = thw + thfp + thbp note5) in case of using the long fr ame period, the deterioration of display quality, noise etc. may be occurred. note6) nclk count of each horizontal scanning time should be always the same. v-blanking period should be ? n ? x ?horizontal scanning time?. ( n : integer) frame period should be always the same. www.datasheet.co.kr datasheet pdf - http://www..net/
(6/8) 2007-05-23 (ver.0.2) LTD133EWDA connector pin assignment for interface cn1 input signal cn1 input signal (20347-040e-02 / i-pex) [ mating connector : 20345-*40t-## / i-pex ] terminal no. symbol function 1 gnd gnd 2 nc non-connection 3 vdd power supply : +3.3v 4 vdd power supply : +3.3v 5 vdd power supply : +3.3v 6 vedid edid 3.3v power 7 nc non-connection 8 clk edid clock 9 data edid data 10 gnd gnd 11 gnd gnd 12 nc non-connection 13 rxin0- negative lvds differential data input (r0-r5, g0) 14 rxin0+ positive lvds differ ential data input (r0-r5, g0) 15 gnd gnd 16 rxin1- negative lvds differential data input (g1-g5, b0-b1) 17 rxin1+ positive lvds differen tial data input (g1-g5, b0-b1) 18 gnd gnd 19 rxin2- negative lvds differential data input (b2-b5, hs, vs, de) 20 rxin2+ positive lvds differenti al data input (b2-b5, hs, vs, de) 21 gnd gnd 22 clk- clock signal(-) 23 clk+ clock signal(+) 24 gnd gnd 25 pwm pwm brightness control (10khz +/- 5%) 26 vbl- led power return 27 vbl- led power return 28 vbl- led power return 29 vbl- led power return 30 vbl- led power return 31 nc non-connection 32 vbl+ 7.5v - 21v led power 33 vbl+ 7.5v - 21v led power 34 vbl+ 7.5v - 21v led power 35 vbl+ 7.5v - 21v led power 36 vbl+ 7.5v - 21v led power 37 nc non-connection 38 smb_clk smbus clock 39 smb_dat smbus data 40 gnd gnd note 1) please connect gnd pin to ground. don' t use it as no-connect nor connection with high impedance. note 2) please connect nc to nothing. don't connect it to ground nor to other signal input. g0 r5 r4 r3 r2 r1 r0 g5 b0 b1 g4 g1 b4 b5 g3 g2 b2 b3 t in4 t in3 t in2 t in1 t in0 tin13 tin12 tin11 tin10 tin9 tin8 tin7 tin20 tin19tin18tin17tin16tin15 tin14 tin6 tin5 hsync vsync de rx in0 rx in1 rx in2 www.datasheet.co.kr datasheet pdf - http://www..net/
(7/8) 2007-05-23 (ver.0.2) LTD133EWDA 256k (k=1024) colors combination table display r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 gray scale level black l l l l l l l l l l l l l l l l l l - blue l l l l l l l l l l l l h h h h h h - green l l l l l l h h h h h h l l l l l l - light blue l l l l l l h h h h h h h h h h h h - red h h h h h h l l l l l l l l l l l l - purple h h h h h h l l l l l l h h h h h h - yello w h h h h h h h h h h h h l l l l l l - basic color white h h h h h h h h h h h h h h h h h h - black l l l l l l l l l l l l l l l l l l l 0 l l l l l h l l l l l l l l l l l l l 1 l l l l h l l l l l l l l l l l l l l 2 : : : : : : l3 l60 h h h h l h l l l l l l l l l l l l l61 dark light h h h h h l l l l l l l l l l l l l l62 gray scale of red red h h h h h h l l l l l l l l l l l l red l63 black l l l l l l l l l l l l l l l l l l l 0 l l l l l l l l l l l h l l l l l l l 1 l l l l l l l l l l h l l l l l l l l 2 : : : : : : l3 l60 l l l l l l h h h h l h l l l l l l l61 dark light l l l l l l h h h h h l l l l l l l l62 gray scale of green green l l l l l l h h h h h h l l l l l l green l63 black l l l l l l l l l l l l l l l l l l l 0 l l l l l l l l l l l l l l l l l h l 1 l l l l l l l l l l l l l l l l h l l 2 : : : : : : l3 l60 l l l l l l l l l l l l h h h h l h l61 dark light l l l l l l l l l l l l h h h h h l l62 gray scale of blue blue l l l l l l l l l l l l h h h h h h blue l63 black l l l l l l l l l l l l l l l l l l l 0 l l l l l h l l l l l h l l l l l h l 1 l l l l h l l l l l h l l l l l h l l 2 : : : : : : l3 l60 h h h h l h h h h h l h h h h h l h l61 dark light h h h h h l h h h h h l h h h h h l l62 gray scale of white & black white h h h h h h h h h h h h h h h h h h white l63 www.datasheet.co.kr datasheet pdf - http://www..net/
(8/8) 2007-05-23 (ver.0.2) LTD133EWDA for safety lcd module is generally designed with precise parts to achieve light weighted thin mechanical dimensions. in using our modules, make certain that you fully understand and put into practice the warnings and safety precautions detailed in engineering informat ion no.ee-d-001a,"cautions and instructions for toshiba matsushita display technology co., ltd lcd modules". refer to individual specifications and technical data s heets (hereinafter called "td") for more detailed technical information. 1) special purposes a) toshiba matsushita display technology's standard lcd modules have not been customized for operation in extreme environments or for use in applications where performance fa ilures could be life-threatening or otherwise catastrophic. b) since toshiba matsushita display technology's standar d lcd modules have not been desi gned for operation in extreme environments, they must never be used in devices that will be exposed to abnormally high levels of vibration or shock which exceed toshiba matsushita display tec hnology's published specification limits. c) in addition, since toshiba matsushita display tec hnology standard lcd modules have not been designed for use in applications where performance failures could be life-threatening or catastrophic, they must never be installed in aircraft navigation control systems (such as, but not limited to traffic collision avoidance system and air traffic indicator), in milit ary defense or weapons systems, in critical indu strial process-control systems (e.g., t hose involved in the production of nuclear energy), or in critical medical devi ce or patient life-support systems. 2) disassembling or modification do not disassemble or modify the module. it may damage sensitive pa rts inside lcd module, and may cause scratches or dust on the display. toshiba matsushita display technology doses not warrant the module, if customer di sassembled or modified it. 3) breakage of lcd panel do not ingest liquid crystal material, do not inhale this material, and do not contact the material with skin, if lcd panel is broken and liquid crystal material spills out. if liquid crystal material comes into mouth or eyes, rinse mouth or eyes out with water immediately. if this material contact with skin or cl oths, wash it off immediately with al cohol and rinse thoroughly with water. 4) glass of lcd panel be careful with chips of glass that may cause in juring fingers or skin, when the glass is broken. 5) electric shock disconnect power supply before handling lcd module. do not touch the parts inside lcd module and the connector or cables in order to prevent electric shock, because high voltage is supplied to these parts from power supply is turned on. 6) absolute maximum ratings and power protection circuit do not exceed the absolute maximum rating values under the worst probable conditions caused by the supply voltage variation, input voltage variation, variation in parts' constants, environmental temperature, etc., otherwise lcd module may be damaged. employ protection circuit for power supply, whe never the specification or td specifies it. suitable protection circuit should be applied for each system design. 7) disposal when dispose lcd module, obey to the applicable environmental regulations. ! www.datasheet.co.kr datasheet pdf - http://www..net/
|
